Home > Articles > Cisco > CCNA Routing and Switching

Cisco CCENT Flash Cards: Understanding Ethernet and Switch Operations

  • Aug 30, 2013
To help in your CCENT preparations, this chapter covers the fundamentals of Ethernet technologies and describes how switches operate.
This chapter is from the book

This chapter is from the book

CCENT ICND1 100-101 Flash Cards and Exam Practice PackCCENT ICND1 100-101 Flash Cards and Exam Practice Pack

Learn More Buy

This chapter is from the book

This chapter is from the book

CCENT ICND1 100-101 Flash Cards and Exam Practice PackCCENT ICND1 100-101 Flash Cards and Exam Practice Pack

Learn More Buy

Section 3. Understanding Ethernet and Switch Operations

Ethernet is the technology of choice for today’s LANs. It is fast, has low costs, and is easy to maintain. Today’s Ethernet standards support speeds of 10 Mbps, 100 Mbps, 1 Gbps, 10 Gbps, and 40 Gbps.

Ethernet functions at Layers 1 and 2 of the Open Systems Interconnection (OSI) model. As such, Ethernet standards specify cabling, signaling, and data link layer addressing.

Because most LANs use Ethernet as the primary Layer 2 technology, most switches today are Ethernet switches. This section covers the fundamentals of Ethernet technologies and describes how switches operate.

Question 1

What does BASE mean in 100BASE-T and 1000BASE-T?

Answer 1

BASE in 100BASE-T and 1000BASE-T refers to the baseband signaling method. Baseband is a network technology in which only one carrier frequency is used. This means that when a device transmits, it uses the entire bandwidth on the wire and does not share it during the single time interval.

Question 2

What is carrier sense multiple access collision detect (CSMA/CD)?

Answer 2

CSMA/CD describes the Ethernet access method.

In CSMA/CD, many stations can transmit on the same cable, and no station has priority over any other. Before a station transmits, it listens on the wire (carrier sense) to make sure that no other station is transmitting. If no other station is transmitting, the station transmits across the wire. If a collision occurs, the transmitting stations detect the collision and run a random backoff algorithm. The random backoff algorithm is a random time that each station waits before retransmitting.

Question 3

What is UTP cabling?

Answer 3

Unshielded twisted-pair (UTP) cabling is a type of twisted-pair cable that relies solely on the cancellation effects produced by the twisted wire pairs to limit electromagnetic interference (EMI) and radio frequency interference (RFI).

UTP cable is often installed using an RJ-45 connector, and UTP cabling must follow precise specifications dictating how many twists are required per meter of cable. The advantages of UTP are ease of installation and low cost. A disadvantage of UTP is that it is more prone to EMI than other types of media.

Question 4

What is the maximum cable length for UTP?

Answer 4

The maximum length is 100 meters or 328 feet.

Question 5

What is a straight-through Ethernet cable, and when would you use it?

Answer 5

A straight-through Ethernet cable is wired the same way at both ends. This cable uses pins 1, 2, 3, and 6. The send and receive wires are not crossed.

You should use a straight-through Ethernet cable when connecting dissimilar devices (for example, data terminal equipment [DTE] to data communications equipment [DCE]). Examples include connecting PCs (DTE) to switches or hubs (DCE) or a router (DTE) to a switch or a hub (DCE).

Question 6

What is a crossover Ethernet cable, and when would you use it?

Answer 6

A crossover Ethernet cable is a cable that has the send and receive wires crossed at one of the ends. In a Category 5 cable, the 1 and 3 wires are switched and the 2 and 6 wires are switched at one end of the cable.

You should use a crossover cable when connecting similar devices (DCE to DCE or DTE to DTE), such as connecting a router to a router, a switch to a switch or hub, a hub to a hub, or a PC to a PC.

NOTE

In today’s networks, most Catalyst switches have auto-mdix, which can automatically detect the type of cable connected to the interface and automatically configure the connection appropriately.

Question 7

What are the different UTP categories?

Answer 7

The categories of UTP cable are as follows:

  • Category 1: Used for telephone communications.
  • Category 2: Capable of data transmission speeds of up to 4 Mbps.
  • Category 3: Used in 10BASE-T networks. Speeds up to 10 Mbps.
  • Category 4: Used in Token Ring networks. Speeds up to 16 Mbps.
  • Category 5: Capable of data transmission speeds of up to 100 Mbps.
  • Category 5e: Supports speeds of up to 1 Gbps.
  • Category 6: Consists of four pairs of 24-gauge copper wires. Speeds up to 1 Gbps.
  • Category 6a: Supports speeds up to 10 Gbps.

Question 8

What is the difference between single-mode fiber (SMF) and multimode fiber (MMF)?

Answer 8

The primary difference between SMF and MMF is the ability of the fiber to send light for a long distance at high bit rates. In general, MMF supports shorter distances than SMF.

Question 9

What are three ways that LAN traffic is transmitted?

Answer 9

LAN traffic is transmitted one of the following three ways:

  • Unicast: Unicasts are the most common type of LAN traffic. A unicast frame is a frame intended for only one host.
  • Broadcast: Broadcast frames are intended for all hosts within a broadcast domain. Stations view broadcast frames as public service announcements. All stations receive and process broadcast frames.
  • Multicast: Multicasts are traffic in which one transmitter tries to reach only a subset, or group, of the entire segment.

Question 10

How many bits are in an Ethernet address?

Answer 10

Also called a MAC address, an Ethernet address is the Layer 2 address associated with the Ethernet network adapter. Typically burned into the adapter, the MAC address is usually displayed in a hexadecimal format, such as 00-0d-65-ac-50-7f.

Question 11

What portion of the MAC address is vendor specific?

Answer 11

The first half or first 24 bits of the MAC address are vendor specific.

A MAC address is 48 bits and is displayed in hexadecimal. The first half of the address identifies the vendor or manufacturer of the card. This is called the Organizational Unique Identifier (OUI). The last half of the address identifies the card address.

Question 12

What portion of the MAC address is vendor assigned?

Answer 12

The last 24 bits are vendor assigned.

Question 13

What are the first 24 bits in a MAC address called?

Answer 13

These bits are the Organizational Unique Identifier (OUI).

Question 14

What is an example of a Layer 2 address?

Answer 14

An example is a MAC address.

Question 15

What is an example of a Layer 3 address?

Answer 15

An example is an IP address.

Question 16

If a sending device does not know the MAC address of the destination device, what protocol is used to find the MAC address of the receiving device?

Answer 16

Address Resolution Protocol (ARP) is used to find the MAC address of the receiving device.

ARP is a local broadcast sent to all devices on the local segment to find the MAC address of a host.

Question 17

Host A wants to send data to host B. Host B is on a different segment from host A. The two segments are connected to each other through a router. What will host B see as the source MAC address for all frames sent from host A?

Answer 17

Because host B is on a different segment that is separated by a router, the MAC address of all frames sent from host A will be the MAC address of the router. Anytime a frame passed through a router, a router rewrites the MAC address to the MAC address of the router’s exit interface for the segment and then sends the frame to the local host.

In this case, the router will change the source MAC address of the frame sent from host A with the MAC address of its interface connecting to the segment host B is on. Host B will see that the frame came from the MAC address of the router with the IP address of host A.

Question 18

Switching uses a process outlined by the IEEE as transparent bridging. What are the five processes transparent bridges use for determining what to do with a frame?

Answer 18

The five processes of transparent bridging as defined in IEEE 802.1d are

  1. Learning
  2. Flooding
  3. Filtering
  4. Forwarding
  5. Aging

Question 19

What is the transparent bridging learning process?

Answer 19

When a frame enters a switch, the switch adds the source Ethernet MAC address and source port into its MAC address table. The process of recording the source MAC address and the source port in the table whenever a switch sees a frame is called the learning process.

Question 20

What is the transparent bridging flooding process?

Answer 20

When a switch receives a unicast frame and it does not have the destination MAC address and port in its bridging table, or a broadcast or multicast frame, the switch will forward this frame out all ports, except the port it received the unicast frame on. This is called the flooding process.

Question 21

What is the transparent bridging filtering process?

Answer 21

The filtering process occurs when a switch receives a frame and the source and destination hosts reside on the same interface. When this occurs, the switch filters or discards the frame. 

Question 22

What is the transparent bridging forwarding process?

Answer 22

A switch forwards a frame when the destination address is in the switch’s MAC address table and the source and destination are on different interfaces. This is the forwarding process.

Question 23

What is the transparent bridging aging process?

Answer 23

When a switch learns a source address, it time-stamps the entry in the MAC address table. Every time the switch sees a frame from the same source, the timestamp is updated. The aging process occurs when the switch does not see a frame from the source before the aging timer expires. When this happens, the switch removes the entry from the MAC address table.

Question 24

For what two purposes does the Ethernet protocol use physical addresses?

Answer 24

Ethernet uses physical addresses to

  • Uniquely identify devices at Layer 2
  • Allow communication between different devices on the same Layer 2 network

Question 25

What will an Ethernet switch do if it receives a unicast frame with a destination MAC that is listed in the switch table?

Answer 25

The switch will forward the frame to a specific port.

Switches use the transparent bridging process to determine how to handle frames. The process is as follows:

  1. A frame is received.
  2. If the destination is a broadcast or multicast, the switch will forward the frame to all ports except to the port the frame was received.
  3. If the destination is a unicast and the address is not in the MAC address table, the switch forwards the frame to all ports except the receiving port.
  4. If the destination is a unicast, the address is in the MAC address table, and the associated interface in the MAC address table is not the receiving interface, the switch forwards the frame to the correct interface.
  5. If the above rules do not occur, filter the frame.

Question 26

Under what conditions would a switch flood a frame?

Answer 26

A switch will flood a frame if the MAC address table is full, if the destination MAC address has not been learned by the switch, or if the frame is a broadcast or multicast frame.

Question 27

What is the switch MAC address table used for?

Answer 27

The switch MAC address table forwards traffic out the appropriate interface.

Because switches operate at Layer 2 of the OSI model, they switch traffic by MAC address. Instead of flooding traffic out all interfaces, a switch learns the MAC address of devices on each interface and only forwards traffic destined to the host on the interface. The learned MAC addresses are stored in the switch’s MAC address table.

Question 28

Describe full-duplex transmission.

Answer 28

Full-duplex transmission is achieved by setting switch interfaces, router ports, and host NICs to full duplex. Microsegmentation, where each network device has its own dedicated segment to the switch, ensures that full duplex will work properly. Because the network device has its own dedicated segment, it does not have to worry about sharing the segment with other devices. With full-duplex transmission, the device can send and receive at the same time, effectively doubling the amount of bandwidth between nodes.

Three points to remember about the operation of full-duplex communication are

  • There are no collisions in full-duplex mode.
  • A dedicated switch port is required for each full-duplex node.
  • The host network card and the switch port must be capable of operating in full-duplex mode.

Question 29

What are the advantages of using full-duplex Ethernet instead of half-duplex?

Answer 29

Full-duplex provides faster data transfer by being able to send and receive simultaneously and operates without collisions.

NOTE

By enabling full-duplex on a port, you are disabling CSMA/CD on the segment.

Question 30

How does replacing a hub with a switch affect CSMA/CD behavior in an Ethernet network?

Answer 30

It effectively eliminates collisions.

Replacing a hub with a switch effectively eliminates collisions because each switch port is a separate collision domain. One device per switch port and configured for full-duplex operation eliminates the need for CSMA/CD.

Question 31

What command allows you to view the duplex and speed settings configured for a switch port?

Answer 31

To view the duplex and speed setting configured for a switch port, enter the show interface interface-id command, as follows:

Click here to view code image

Cat2960# show interface f0/1
FastEthernet0/1 is up, line protocol is up
  Hardware is Fast Ethernet, address is 0019.e81a.4801
     (bia 0019.e81a.4801)
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Auto-duplex, Auto-speed, media type is 10/100BaseTX            
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00

Question 32

Can a network hub be connected to a switch port in full-duplex mode?

Answer 32

No. Because a hub shares access to the segment, it must connect to a switch port in half-duplex mode to be able to detect collisions.

NOTE

CSMA/CD is not enforced when full-duplex is configured.

Question 33

When troubleshooting a switch interface operating in full-duplex mode, which error condition can be immediately ruled out?

Answer 33

Collisions can be ruled out.

Remember, collisions occur only on half-duplex links. There are no collisions on full-duplex links.

Question 34

An end user complains of slow access to the network. You issue the show interface command on the port the end user is connected to and you see a lot of collisions and runts on the interface. What is most likely the cause of the problem?

Answer 34

A duplex mismatch is most likely the cause.

Although there are many things that can cause network slowness, the key here is when you issue the show interface command, you see many collisions and runts. A duplex mismatch will not only cause the end user to experience network slowness but also cause many collisions and runts on the switch interface.

Question 35

An end user complains of slow access to the network. You issue the show interface command on the port the user is connected to and you see a lot of collisions and cyclic redundancy check (CRC) errors on the interface. What can be several causes for the problem?

Answer 35

The most likely causes of the problem are a bad network cable, damaged media, or EMI.

Excessive collisions and CRC errors usually indicate a problem with the network cable attached to the port, or outside interference.

Question 36

You connect two switches using a straight-through UTP Cat 6 cable. The port link lights between the switches are not coming on. What is the problem?

Answer 36

The problem is with the cable. A straight-through cable is used to connect data terminal equipment (DTE) devices to data communications equipment (DCE) devices. A switch is considered a DCE device, and so are hubs. DTE devices include computers, printers, servers, and routers. For two like devices to connect to each other, a crossover cable is needed. In this case, replacing the cable with a crossover cable will fix the problem.

Question 37

You have a port on your switch that is not working properly. You enter the show interface command on the faulty port and the port status says “errDisable.” What are some possible causes for this error?

Answer 37

If you are having connectivity issues and the port state shows “errDisable,” the following issues can be causing this error:

  • EtherChannel misconfiguration.
  • Duplex mismatch.
  • Bridge protocol data unit (BPDU) port guard has been enabled on the port.
  • Unidirectional Link Detection (UDLD).
  • A native VLAN mismatch.

Question 38

Traffic between two switches is slow. You issue the show interface command on the uplink between the two switches and you see the following:

!output omitted!
0 input packets with dribble condition detected
     180749 packets output, 8004302 bytes, 0 underruns
     0 output errors, 45345 collisions, 0 interface resets
     0 babbles, 45345 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

What are several possibilities for this problem?

Answer 38

The switch port is receiving a lot of late collisions. The problem can be a duplex mismatch or a faulty port, or the distance between the two switches might exceed the cable specifications.

NOTE

Duplex mismatches occur when the connecting ends are set to different duplex modes, or when one end’s duplex is configured and the other end is set to autonegotiation.

Question 39

What is the cause of multiple collisions on a port?

Answer 39

Multiple collisions are the number of times the transmitting port had more than one collision before successfully transmitting a frame. If you experience multiple collisions on a port, the problem usually lies with an oversaturated medium.

Question 40

While troubleshooting a switched network, you see the following on a switch interface that is having connectivity problems:

!output omitted!
  5 minute input rate 10000 bits/sec, 8 packets/sec
  5 minute output rate 10000 bits/sec, 7 packets/sec
     1476671 packets input, 363178961 bytes, 0 no buffer
     Received 20320 broadcasts (12683 multicast)
     2345 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

What could be the cause of the problem?

Answer 40

The switch is receiving a lot of runts. Runts are frames smaller than 64 bytes with a bad frame check sequence (FCS). Bad cabling or inconsistent duplex settings usually cause runts.

Pearson IT Certification Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Pearson IT Certification and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Pearson IT Certification products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by Adobe Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.pearsonitcertification.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020